Transcription
Hey, I'm Brian Hiebert from Leisure Travel Vans
and today we're going
to be walking through the
winterization process on
your coach using RV anti-freeze.
This is going to apply to both the Unity
and the Wonder products.
So the first thing we're going to start
with is make sure that
all of our tanks are empty.
We're going to take a look at our gauges
inside first of all to
make sure that's empty and
if they're not empty they
do need to be dumped as well.
So take your coach to a dump station for
the black and grey tank
and also for the fresh
tank that you can just open up because it
is fresh water that's
okay if that can run
onto the ground.
So here we are over
at the Firefly screen.
We're just going to go over to the tanks
and you can see this
coach they are all empty.
The fresh grey and black they're all
currently empty so that's
good that's what we want to
see.
If they're not do make sure that they are
all dumped and
completely drained before starting
the winterization process.
Next thing we're going to do is just make
sure that the water
heater is turned off as
well.
So the water heater here just make sure
that it's not on eco or
comfort make sure it is
turned off.
Once it's turned off we're going to save
that and always make
sure that the water heater
is cooled off to the touch as well before
you start this because
we are going to drain
it and when we're going to drain it we
don't want to have that
under pressure but also
that we don't want hot water coming out
at us when we do that.
So next thing we're going to do is just
make sure that the
valves are set correctly and
also that the water
heater has cooled off.
So in this case we're in a Unity MBL the
water heater is located
underneath here in the galley.
We're going to make sure all the valves
are set correctly we'll
go through that in just
a second but also we're just going to
make sure that the water
heater is actually cool
to the touch so just when we put our
hands on there make
sure it's cool to the touch
so that we don't have any of that hot
water coming out at us later on.
Now we're on the outside of the coach
we're just going to open
up the water heater door
and you can see that it's still currently
turned on the green
light is on so we're just
going to turn this off.
To turn it off you're going to turn it to
the middle position.
It does have a lower position as well but
that's going to keep it on make sure that
it's turned to the middle off position
and if the water heater
is not cool to the touch
yet and inside or even out here on the
mixing tank you can
always go back inside the coach
and you can run some water through the
hot lines just to cool it
off a little bit quicker
if you're still hooked up to water.
If you're not hooked up to water just let
it cool off and then
come back to this after
maybe another 10-20 minutes or so.
Next thing we're going to do is make sure
that the fresh tank is completely drained
as well.
So in this case on the MBL we do have
this extension here that
we can use to drain the
fresh tank.
On some coaches it'll be inside so you're
going to have a valve
inside so it'll vary
depending on the floor plan.
In this case it's an MBL so we're just
going to go down here
we're going to find the drain
right here and we can just turn that in
order to drain it and
let all the water come out
of the fresh tank and you can just leave
the drain open over
winter as well just to
make sure that all the
water comes out of there.
We'll head back inside the coaching we're
going to turn on the
water pump for a while
and open up a couple of faucets and let
any residual water
drain out of those lines.
We're going to let that happen make sure
everything is clear.
Once that happens we'll come back and
we'll just turn that
water pump back off again.
So now that we have the water pump turned
off and there's no city
water connection connected
to the coach so make sure there's no
pressure in there we're
also going to open up a faucet
just to make sure that there is no
pressure in the line.
So this is both for the cold and the hot
we'll keep it this one in
right about in the middle
so that way it's relieving pressure from
both the hot and the
cold lines right now.
So no pressure in the lines and we're
just going to leave it like this.
At this point we can go outside and we
can drain the hot water
heater because there shouldn't
be any pressure in the hot lines.
So now that the water heater has been
turned off and it's
cooled off we're going to just
drain the water heater.
We're going to drop this yellow lever and
in order to do that
there's a black tab on
here we're just going to push up on that
black tab a little bit
so that that comes free.
And now at this point you want to make
sure you stand clear
because if there's water inside
the heater it will be coming out so just
stand clear because you don't want to get
wet.
But we're going to drop
this all the way down.
When you do that the in that filter is
going to pop out a little bit.
This in that filter you want to take this
out completely and
store this inside the coach
somewhere.
Don't leave it in during winter storage
so make sure you take
it out and leave it out.
Once the water has all drained out then
we can lift this back
up, clip it back into place
and again we're going to store this in
that filter inside the coach somewhere.
Okay so we're going to turn the water
heater over to bypass mode.
In this case we're in a corner bed.
You're going to see that each valve is
labeled A, B, C, D and E.
There's five valves in total.
You've got the little labels right on the
sides of the valve on the water lines.
You're going to see that the red lines,
those are the hot water lines.
Blue is the cold.
So the way the water flows in here is
it's going to come in
from the blue line, go into
the water heater and then back out
through the hot line.
Open is always parallel to the water
line, not perpendicular.
So if you look at this valve right now
for example this one's
turned off because it's
perpendicular to the water line.
Once we turn it parallel to the water
line like this that is open.
So it will depend on which position it's
in, if it's open or closed.
You don't ever look at it if it's
horizontal or vertical.
Always look to see if it's
parallel or perpendicular.
So parallel is open.
And in order to turn it into bypass mode
we're going to take valve A and close it.
E we're going to close
and B we're going to close.
D remains closed, it was closed already.
And then C we're going to open.
So right now we got A, E,
D and B they're all closed.
And C is open.
That's in bypass mode.
Our next step is to ensure that the water
filter is empty as well.
So we're going to drain the water filter.
First thing we're going to do is grab
this filter wrench,
we're going to grab this and
a couple of towels as well.
Because when we do take that filter off
there may be some water
that's going to come out.
So get some towels underneath there and
then we're going to
use this to remove it.
You never use this to install it by the
way, this is only used to remove it.
So you're going to use this wrench to
remove the filter casing.
And once you get the casing out you're
going to see that there's
a charcoal filter in there.
And that charcoal filter does need to be
removed for winterizing.
Ideally you do want
to replace it as well.
Not at this point but maybe in spring
time when it's time to get
your coach up and running
again you're going to want
to replace this cartridge.
But for now we're going to take that
cartridge out and make
sure that the water canister
is drained from any water as well.
So we're back out here by the service
compartment and what we're
going to do is we're going
to make sure that our tank fill valve is
set to normal and city water.
So we're going to turn the valve this way
to make sure it's on
normal and city water.
And then the winterized valve we're going
to turn that one over to winterized.
So now it's set to winterized.
Once we have it set there we're going to
pull out the winterization holes.
So you're going to
find this holes in here.
This one end is attached to the
winterization valve, the
other one is just a free end.
That's the end that we're going to put
into the RV anaphrase jug.
And we're going to make sure that we're
using RV anaphrase not
any kind of other anaphrase.
It has to be safe for RV use as well.
So we're going to open up this jug and
we're just going to put that in there.
That way the pump can draw from here.
So now when we turn the water pump on it
will actually draw the
anaphrase up through here
and into the coach and
into the water lines.
So we've got the anaphrase jug hooked up
outside ready to go.
We're going to turn on the water pump and
we're going to let RV
anaphrase run through
each one of the faucets and ensuring that
there is good pink
fluid coming out of each
faucet.
So we'll turn on the water pump.
You'll hear it pressurize.
And you're going to want to make sure
that you run anaphrase
through each side, both
the cold and the hot side.
So let it run for a
little bit at each location.
Get a good stream of flow from the cold
and then we'll switch
it over to the hot side
and make sure we do the hot as well.
Once you see a good flow you can shut
that off and do that at
each faucet including the
galley, the vanity, the inside shower,
toilet and the exterior shower as well.
So the most important thing to remember
at the shower faucet
here is don't open it all
the way immediately because that's only
going to take you right to the full hot.
So you want to make sure
you start on the slow side.
Let it run so you see pink fluid.
Once you see that pink fluid then turn it
all the way up to hot
and do the hot as well.
So again ensure that you don't just flip
it straight over to
hot because you're only
getting the hot at that point.
Make sure you get both
the cold and then the hot.
So the other thing we want to drain is
the circulation line
for the water heater.
That's going to be valve D. So we're
going to open that up for
just a second or two just
to make sure that there's pink fluid
coming out of that as well.
That's just going to be
draining outside onto the ground.
So all we're going to do is just flip
this open for just a couple seconds.
And ideally if you do have a second
person have them take a
look outside and make sure
that there's actually pink fluid coming
out of there as well.
So now that we have pink fluid coming out
of every faucet what we're going to do is
just shut the water pump off and we'll
just release the pressure
in the water lines again.
So again we'll just open it up kind of
halfway between the cold and the hot.
We'll just open it up right there and let
all that pressure out.
So here we're back at
the city water fill.
It's got a little screen in there.
We're going to pull this screen out.
The screen in the gasket
we're just going to pull that out.
And there's a little
check valve inside here.
We want to make sure that
this is also winterized.
But never do this while there's pressure
on the water lines
because that check valve
inside there there's a seal in there and
that seal will blow out.
So we're going to just make sure that
there is no pressure
inside the water lines.
You can even hold in the exterior shower
just to make sure there's no pressure.
And we're just going to
burp this a little bit.
We're going to press that in and you can
see that there's some
antifreeze that came out.
If no antifreeze came out hold the check
valve in and you can burp
the pump for just a second.
So I'll turn it on for just a second and
then turn it off and you
can see that some antifreeze
comes out.
That will make sure that that
line is now winterized as well.
So as soon as we're done winterizing the
city water connection
we're going to make sure
that we put the gasket
with the screen back in place.
And make sure it's in
there the right way.
You want to make sure
it's not pointed in.
It's got to be pointed out as well
otherwise you could
potentially be pushing that check
valve in.
So we're just going to make sure we
replace that and make
sure it's fully seated.
That way it's ready for springtime again.
So one optional step we can do at this
point as well is blow some
air through the antifresh
line.
So the sandy flush line is
for rinsing the black tank.
So this line will go up into the coach
and there's going to be
a check valve in there
which also has a backflow preventers.
So the water will go up into there and
then go back down
towards the black tank and on
the black tank there's a couple of jets
that are actually
rinsing out the inside of the
tank.
So there really shouldn't be any water in
here because the water will drain out.
So long as this is open, left open there
will be water draining
out here when you're done
the sandy flush process and also back
into the black tank.
It will drain itself out.
But just to make sure we can shoot a
little bit of compressed
air into there, that's going
to push that back all the way into the
black tank making sure
nothing is P-trapped and
that there's no trapped
up water in there as well.
No need to run any
antifreeze through this.
So at this point we also want to make
sure that if your coach
is equipped with a mass
rater that we run some antifreeze through
the mass rater as well.
So this is through the black tank so
again you probably want
to be at a dump station
or you may have to run this
into a bucket or something.
But we're just going to turn on the mass
air switch because
there is antifreeze in the
tank right now and it
went into the black tank.
We're just going to turn on the mass
rater for a bit and just
make sure that that comes
out of the mass rater as well.
So ideally here we also want to make sure
all the fluids are
drained out of the fresh
tank again because we did run some
antifreeze through there.
So you may want to drain the tanks again,
the grey and the black
just to make sure that
there is no fluid left in there.
If there's some antifreeze left in there
that's totally fine if
that's all that's in there.
But if you do want to make sure they're
completely drained you can
always take it back to a dump
station and make sure it's completely
drained or if there's
just a little bit maybe into
a bucket or something like that as well.
Next thing we want to do is just make
sure that the winterized
valve is turned back to
normal flow.
So we'll turn it back this way so it's
pointed back to normal flow as well.
So this might be a good time to just
maintain the inlet
filter on the water pump.
There's a screen right here that we can
remove that canister and
then we can take that screen
out and give it a good cleaning.
Well I would always recommend to make
sure you do have some
towels or something on hand
because there might be some water coming
out when you do take this off.
So we're going to put that underneath
there and always make
sure that the pressures are
released inside the water lines as well
just in case if there
is any pressure on there.
So in order to remove this, this is just
going to be hand tight
so we're going to loosen
that off as we unscrew that canister.
You're going to see
that this is the screen.
That can be popped out
and that can be cleaned.
And when it's time to put it back on make
sure that this gasket is in place here as
well.
There's a gasket just inside this inner
ring just to make sure that's in place.
We're going to take this
screen, put the screen back in.
There is a little bit of a bump on the
inside here, a little bit
of a recess let's say that
that will slip into so that
kind of keeps it in place.
Now when it comes time to install it
we'll just make sure that
that screen stays in place,
the gasket stays in place.
Don't tighten it with a wrench or
anything just tighten it a
little bit by hand that's
all you really need to do to seal it and
that's all that's required.
We're going to remove
the water filter canister.
If you need to you can use
the wrench to loosen it off.
So we'll just get this up into there and
you can just use this to loosen that off.
Don't ever use this to install it just
always make sure this is
only used just to loosen
it off.
Once you have it loose you can take it
off and just be
careful removing this because
it will likely be full of water.
We're going to pull that canister and
just drain out of a
fluid that's left in there
just so it doesn't sit
in there over winter.
There is a gasket inside here just make
sure that o-ring is in place.
If you've lost it that will need to be
replaced and it will leak
if you've lost it so just
make sure that o-ring is in
place before reinstalling it.
So when you're reinstalling it we're just
going to tighten this
by hand that's all it
needs to seal.
Don't use the wrench to tighten it up.
The next thing we're going to do is just
come to each one of the
sinks that we're at and
just make sure that those are left clean
as well because we don't
want that fluid to stay
in the sinks or the shower
pan or anything like that.
So we're just going to come along and
we're going to clean
those to make sure everything
is spotless so it's ready for springtime.
you