Hey, I'm Brian Hebert from Leisure Travel Vans,
and today we're gonna be talking a little bit about the
routine step maintenance
for the exterior step on your coach.
So the step we're referring to here is this step right here.
This is a power step, so it has a motor underneath here
and as well as a module that controls that.
You'll see a light that actually turns on
whenever the step is active as well.
Step moves in when the door is closed,
provided the step override is not turned on.
So what we always wanna do is make sure
that all the lubrication points are lubricated
for, uh, proper function.
So the first thing that you're gonna wanna do is make sure
there's no extra dirt
and debris inside all these contact points.
So you're gonna wanna start off by washing the step down.
Usually if you get a lot of rolled grime
and debris on there, some sand
and stuff like that, you wanna make sure
that you wash all that off first.
So typical washing with, uh, garden hose, maybe even a bit
of soap water if need be.
So that's gonna be your first step is washing all the parts
here and also pay
attention to the parts that are underneath.
I'll show you that a little bit later as well.
So the step is built by quickie,
Lippert and Quickie Lippert.
They recommend in the manual for the step that they,
you use what's called quick lube.
The Quick lube, it's a bit of a heavier grease.
It's not a silicone or a WD 40 or dry lube.
If you use something like a dry lube silicone spray
or the like, that'll end up needing
to be used almost daily on this step
and really won't be sufficient
for lubricating this step for proper function.
So again, you wanna use something a little bit
of a heavier grease to make sure that it actually penetrates
and also stays in place as well.
So again, we're gonna touch these contact points
so you can see a couple pivot points and,
and sliding points here,
as well as down here on the mechanism.
So again, we're just gonna make sure
that we lubricate these spots, Get inside each one.
And what you can do as well is
after you've lubricated those points, operate the step
to make sure it actually gets in place.
You can even do that a couple times.
Do that on all the contact points.
Clean up any excess as well, so you don't have any
excessive grease sitting on there.
Once that sets up,
this quick lube will be a little bit thicker
and it'll set up a little bit, a little bit thicker than
what you would see again
with the dry lube or something like that.
So we'll show you, this is the bottom of the step right now.
So this is upside down. What you're gonna see is the the
motor, what module and the light.
That's what's underneath here.
And we're gonna show you some of these contact points.
So this arm, this mechanism here, as well as even in here,
these are the important parts
that you wanna make sure you lubricate as well.
So again, this is gonna be upside down right now,
but later on when you have it on the coach,
this will all be upside down.
So you're gonna make sure you lubricate all those spots
As well as we're gonna come along
and again, hit these points,
making sure you get every one of them.
So I'll just go along and I'll hit every one of these spots
that we can see, making sure we don't forget any of them.
And even in here too, there's a bit
of a bushing in here right where the rod passes through.
So there's a bit of a bushing there.
We wanna make sure we get that as well.
And even on both sides, if need be.
And again, at this point, I'd operate the steps a few times
just to make sure that works its way in place.
And once you have it in place, you're just gonna come along
and just gonna clean up the excess just
to make sure we don't have too much sitting
there on the surface.
And once this is set up, it's gonna be a little bit thicker
and that's what you want in order to
ensure the step functions properly.
So again, we're gonna make sure we got every point
there, clean it all up.
And this is something that you'll probably have
to do at least once a month, maybe less,
or maybe more dependent on the use
or how dirty the roads are that you've been driving on.
But in general, you wanna do this at least once a
month or as needed.
So the quickie Lippert step is installed on all