Comment vider vos réservoirs en cas de panne du broyeur
Qu'est-ce que c'est et comment ça fonctionne?
Vérifiez si l'arbre de pompe bloqué peut être dégagé, puis retirez la pompe et raccordez le 3-inch boyau de vidange par gravité pour vider vos réservoirs.
Hi, I'm Daryl from Leisure Travel Vans.
Today we're going to go over the removal
of a merator pump. We're going to be
demonstrating on a Unity uh but it's the
same principle on a Wonder as well. If
you guys are ever in a situation where
the merator pump doesn't work and you
need to dump the tanks, we're going to
go over how to remove this pump and
connect the 3-in gravity drain line. For
tools, you're going to need something to
cut the tie straps holding the wire.
We're going to use side cutters. You can
use a knife. Uh you're going to need a
flatb blade screwdriver or a 5/16 nut
driver to undo uh two clamps. There's
one supporting the back of the pump.
There's one holding the hose to the
pump. Before we do that, uh there is a
chance the pump is stuck and it can be
freed by turning the actual pump shaft
uh with a screwdriver.
And I'm going to show you guys how to do
that as well. So, before we remove the
pump, we're going to try freeing the
pump. Uh hoping that's the issue. So, to
do that, we're going to loosen off these
two Phillips screws. You don't need to
take them out completely. Uh they just
need to be loosened off at which point
you should be able to this will pivot
one way. Pivot pivot that out of the
way. And then with a flatb blade
screwdriver, we're going to turn the end
of the shaft uh to see if the pump is
turning.
This one turns freely.
Uh so the problem must be something
else. Uh sometimes there can be
something clogging the impeller and by
turning the shaft uh you can get it
unstuck and the pump will work again. Uh
now we're just going to proceed uh with
removing the pump. We're going to cut
these two tie straps holding the wires.
And you can use a side cutter is best.
You can use a knife or anything you else
you have to cut these straps.
With those straps cut, we're going to
find the connector.
There's probably going to be another
strap here that will need to be cut.
To actually get at the connector,
you're going to peel the wire loom off.
And there's our connector. Uh, it's got
a tab you pull and you can unplug it.
So, we're going to undo this clamp
first. Uh, to take the hose off, you're
going to want to wear gloves at this
point. Uh, this is a brand new coach, so
we don't have to worry about that.
We're going to undo
this clamp.
Get this hose pulled off the pump.
And you're going to have some liquid
spilling out at this point. Push the
hose up into the compartment.
And you're going to want to make sure
your gate valves are closed uh before
you pull the pump. And then come back
out here. undo the gear clamp supporting
the back of the pump.
At this point, we should be able to just
give the pump a quarter turn or eighth
of a turn counterclockwise
to get it off the bayonet fitting.
At this point, we're going to grab our
gravity drain hose. Every coach comes
with a 3-in gravity drain hose, even if
it is equipped with a master door pump.
On this one, uh the hose is stored in
this compartment.
We're going to grab that hose.
One end of the hose is going to have the
fitting to lock onto these tabs.
Give it a turn. Lock it on. And at this
point, you can drain your tanks using
gravity same way you would otherwise,
dumping your black tank first and then
your gray tank.