Hey, I'm Brian from these your travel Vans. And today we're gonna be talking about how to perform
an amp draw test on your batteries. So to perform
the amp draw test on the batteries, what we're going to need is a voltmeter and
it needs to be in a voltmeter that's actually capable of doing
amps DC. So in
this case, we flick that over to amps DC and typically what
we'd like to use is a clamp meter as well because that way you can clamp directly
over top of the cable. It makes it all a lot simpler to
use in some cases. They will just use the cable leads like
this that can be used as well and we might also be using this just to
check the actual voltage on the batteries as well. So the reason for doing a
battery draw is just to make sure that we don't have an excessive draw on the
batteries excess of power coming out of the batteries and things
that draw from the batteries are the 12 volt systems like the
lighting inside the coach in this case a multiplex
system any of those items that are run by the 12 volt batteries.
They are creating a draw on the batteries. We're in there in use. So first thing
we want to do is make sure the house battery is fully charged. You can see this
one sitting on at least 14.3. So it is fully charged right
now that will give us a good base line to make sure the voltage is good.
The batteries so whenever we do the battery Java we want to do is make sure the battery
disconnect is turned on but then make sure every component
that we know of is turned off. And then at that point we can
determine how much draw is coming out of the batteries. So we're going to do is
again make sure the battery disconnect is turned on we're gonna unplug the
short power and make sure the inverter is turned off as well.
So another thing to make sure of is the solar panels as
well. We want to make sure that you're either indoors. So they're not getting any sunlight
or that you have them covered up. Another option would
be to disconnect them by the fuse inside the
battery compartment. You can always pull that fuse to make sure that they're completely disconnected and
no power is being put into the batteries from the
solar panels. So to access the solar panel feels we'll have to
pull the batteries forward. So this being a Unity when they're inside the step
of the entrance here.
So we'll open this up.
pull this panel out first
and then this time here.
Okay. So once we have those panels
out of the way, we'll pull the batteries for
Once we have the batteries forward the fuse will be an inline fuse
in the back of the battery compartment. You're going to see how it's actually
hooked up to the main Mega fuse block so we
can open up the cover for that fuse holder and remove the
fuse. So this is the fuse holder right here. The fuse
is inside there. So we'll have to open this up in order to actually
get at the fuse. So in order to remove the fuse, there's just a clip on
here that you have to lift up. Once you have that lift it up. You can just open that cover
up and here you'll see the fuse for the solar panels.
once you remove this fuse
There's no power coming into the batteries anymore from the solar panels
to replace the fuse again. You just make sure that the seated
properly if they're seated below the terminals that's
not correct. Make sure they're both properly inside the
terminals.
And it is fully seated.
Yeah, once it's fully seated put the cover back on to
make sure it stays water tight.
So if by chance you've got a draw on your coach that is still
fairly high and you want to determine exactly what that draw is. You can
actually pull individual fuses. You can see that brings the
amp draw down. Once you find the fuse that it has actually
creating the amp draw you can correspond that
to the label inside the fuse panel and once you
find which fuse it's under you go to that component and
see if that component is still turned on or if it is the one that's actually creating
a drawn something else needs to be resolved. So we're gonna make sure that the fans
are also turned off. So in order to turn them off, we're gonna turn them all
the way to zero.
That'll turn the fans off. We'll also make sure we turn the fridge
off because it'll be using power to run the circuit
board. We'll make sure that we turn off the leveling jacks
make sure they're not turned on once those items are turned off
and unplugged then we're also go through the coach and again turn everything off. So
including all the lights so we'll make sure all the lights are turned off. We'll
turn off all the lights will turn off everything else that we know of
that runs off of 12 volt power. They're will always be something that will create a
draw so long as a battery disconnect is turned on things like the
multiplex system will still be running in the background as well
as the carbon monoxide detector. These things are things will
always be power so they will always create a little bit of a draw with the battery disconnect turned on.
Will come outside to do the battery draw and just remember that whenever we're
opening up the door the step is running off of the household power. But soul
is the light on that's underneath there. Give it enough time. I
think it's about 10 minutes the light will turn off and stop that
draw as well. But that's another thing to remember that there is a light underneath the
step that we'll be creating a draw on the batteries. We'll pull the batteries forward
so we can access the cables.
so what we're gonna do now is
we're gonna use a clamp meter to actually do the battery draw test and we're
gonna make sure that we turn the
the voltmeter all the way to amps DC
That we can measure the DC amps being drawn out of the batteries. So
another thing we want to do before we start the test you'll see that we need
to zero out the monitor.
So we're just going to zero that out make sure it's at zero and then we can clamp it
over top of the cable. So in this case, we've got lithium batteries.
The lithium batteries are both 12 volts. So they're wired in parallel
to produce 12 volts if it
is.