Hey, I'm Willie from Leisure Travel
Vans. Today, we're going to show you how
to winterize the RV with a Truma Aqua
Gold Comfort Plus water heater. Okay.
And some of the tools you're going to
need is uh 2 gallons of RV non-toxic
plumbing antifreeze and um an air chuck
and some paper towel. What we're going
to do is turn off the water pump and
we're going to turn off the water
heater. This unit is equipped with a
switch inside. I would recommend if you
have the switch inside that you leave
this switch on at all times. On the
previous models, the switch was outside
on the water heater itself. So, you have
to come out here and make sure you turn
it off over here. We're going to
depressurize the water line. So, what
I'm going to do is take the pressure off
by opening up this faucet. And it can be
any faucet, but I always prefer to do
the kitchen one first. And now what
we're going to do is we're going to turn
off the propane outside here at in the
utility compartment. We're also going to
disconnect the city water connection
right here.
Okay, I'm going to go drain the
freshwater tank right now. The Unity
Murphy bed and FX have it underneath the
floor outside. The twin bed, corner bed,
and island bed. It's underneath the bed
inside. Okay. The freshwater tank drain
is right here. So, what you want to do
is open this up. And if it was mine, I
would leave it open for the winter or
however long you store it so that the
there's any water left in the tank so it
can drain. Okay. Now, what we're going
to do is we're going to open up the
water heater and we're going to drain
the water heater itself. So, we're going
to do is open up the pressure relief
valve
so there's no pressure in our lines. And
then what we're going to do is open up
this yellow easy drain lever.
But make sure that the water is not too
hot that it'll be so you'll get burned
or scolded by this water.
You open this up.
You take out this screen.
And then at this point, you can close
the water heater lever. The water is
still coming out cuz the seal is in my
hand.
And this screen we will store inside in
a warm dry place. Preferably in a dry
place at least. So, we usually leave it
in the drawer of the coach. All I do is
put the uh screen filter in here in a
plastic bag and we leave it in here for
the winter
and store it in the drawer.
I'm going to go underneath there and
turn the water heater bypass valves to
bypass. So, I'm going to close valves A,
B,
and E.
That's bypass and water heater valve.
The the other two valves in the back,
the one with a white hose on it is your
drain, water tank drain. And the other
one is your um circulation line. So
those two, the one on the far right,
valve C,
leave that open. And valve
D should remain closed. Okay. At this
point, we're going to take this U filter
out of the the canister. So, I'm I got
this tool right here, and that fits up.
It fits onto here,
and you you unscrew that. Then, I have a
little container in case I drip some
water. We're going to put that
underneath there.
Then we're going to take the filter
out of the canister
and dump the water that's in the
canister out of there. And before we put
this back on, we want to make sure that
this rubber ring is in place. Otherwise,
you'll have a leak.
You tighten it up snug by hand is good
enough. I'm going to leave the filter in
the sink. so it can dry out. And that's
because we're going to use it again
later on in spring or whenever we decide
to uh dewinterize our coach. What we're
going to do is we're going to grab this
hose off the blue winterization
valve. And then what we're going to do
is put this hose into a jug of non toxic
plumbing antifreeze. Put this into
there. You turn this valve right here
over to winterize.
And you make sure that your city water
tank fill is on city water. Otherwise,
you'll be pumping it through your tank
and you don't want to get it into your
tank. And that's also the same reason
that we did the valves inside on the
water heater. We want to make sure that
we don't get any winterization fluid
into the water heater. What we're going
to do is we're going to turn on the
water pump and then we're going to go to
each faucet
and we're going to make sure that we
have
pink stuff till we see pink stuff coming
through. So, make sure you do hot and
cold at each faucet.
There we go. And then you turn it to hot
or cold and do the same thing. You do
that on each faucet like I said.
And once you see the pink, you can turn
it off. And again the same way.
I noticed that our pump was running
inside and it wasn't getting any uh
fluid. So it we're going to replace this
jug. So now we're going to winterize the
toilet.
Press on the lever till you see some
pink stuff coming through there, which
we're seeing right now. Also make sure
you see some pink stuff coming through
this little rinse hose here.
Okay. So, right now we're going to do
the outside shower.
Open that up. See the pig stuff coming.
That's that one. And now we have it
coming on the the other hot and cold.
And that is good for now. Now I'm going
to go inside and turn off the water pump
so that I can press this little button
in on this behind the screen. We're just
going to turn off the water pump. And as
far as I'm concerned up here, we're
done. Then we're going to go and take
the pressure off the water line.
So when I press that little button, the
city water tank fill so that we don't
blow the gasket out of there. Okay. So
now what we're going to do is we're
going to take out this screen on the
city water fill here. And then before we
uh release this button, we want to make
sure that the pump is turned off and the
pressure has been released. If we don't
do that first, the rubber seal inside
that valve will will blow out. So, you
want to make sure you do all that
beforehand. Turn off the pump and
release the pressure before you press
this button. If you happen to have a
second person inside, would be nice to
somebody to operate the switch on the
water pump so that we will uh burp the
pump means pressing pressing the on and
off switch a few times just so you don't
get too much pressure over here and yet
you won't have antifreeze coming out of
here. And we're going to press in that
little lever that's inside there, that
little ball. As you can see, there's
till we get fluid coming, we know we
release the water. And you replace the
screen
and put the cap back on. And what you
might want to do is turn this thing this
valve back to normal flow.
Okay. So, valve D, which is the water
water line drain, which is right here.
We want to open that up. So, whatever we
have in the line so that can drain out.
And now the next step is to uh remove
the canister. Again, you want to drain
the fluid out of the canister. There's
no reason for the fluid to stay in there
all winter.
And you can just dump this down the
sink.
Again, make sure your your rubber ring
is there.
Just put this back in place.
And at this point, you want to make sure
it's tight.
Okay. So, at this point, what is
recommended that you wipe out the sink,
all the sinks and toilets, so that you
don't get staining in the toilet from
the winterization fluid.
What we want to do is want to make sure
that our that our gray and black tanks
are empty. If you have the optional
merator pump, you want to take out this
hose, remove this cap,
and open up your gray and black tanks.
Your black should always be opened up
first. And you want to drain that. Turn
on your pump
until
once this quits pumping
until your black tank is empty. And what
once that is done, you open up your gray
so that your gray will help rinse the
black. Make sure that your tanks are
completely empty when you're done.
Because this is a new unit, I'm draining
this inside. But once you have had the
unit, make sure you go to a sewer dump
to dump your tanks. And then you turn
off the water pump. But do not let the
pump run dry.
Preferably, it should uh there should be
some fluid in there. Although these are
waterless P traps, you should still dump
some antifreeze down each sink to make
sure that each uh pipe got some.
about a cup
give or take would be good. And you do
that at each
sink. Once you've uh done that,
and I have a little bit of extra left
here because we have the miserator pump
on this coach, we want to make sure that
the pump gets enough winterization so
that doesn't freeze on us. So, I'm going
to dump that down the bathroom sink. So,
you should probably dump an extra two
cups in there if it has a mistator pump.
If you don't have the merator pump, you
will have the the hose that's that comes
along with the coach, which is stored up
between the two baggage compartments,
and you can hook that up there where
this pump is now connected. Because we
dumped a little bit of extra antifreeze
in there, we just want to make sure that
we pump that out of the system yet, too.
there. And that should do it. We're
going to close the tanks.
And then we're going to put the cap back
onto the sewer hose. And then we're
going to put the sewer hose back in
place.
And as far as uh draining the tanks and
that all goes, we're done with that. The
only other thing we need to do is blow
some air into the black tank flush. So,
just so that make sure that we don't
have no water trapped in there. So, I
have this connection which I'm going to
put onto here. Before we uh we put air
into the tank. We want to make sure that
their valves are open so we don't by
accident blow too much air into the tank
and therefore pressurizes backwards into
the sinks.
So, right now I'm going to hook this up
and my valves are open. And that's how
you have to make sure you do it. Blow
some air through the system for about 15
seconds or so.
It doesn't need to be very long cuz
there's probably not any water left in
there anyway.
But if you do it for 15 seconds or so,
you should be good. Remove this plug.
Put the cap back in place. Store in
utility compartment.
And then you clean up this uh
winterization hose.
Put that back in place. And folks, that
should be it.