Hey, I'm Brian from Leisure Travel Vans. And today we're going to be talking about some of the common problems.
You might find with the entrance door lock and the keyless lock
on your engine store. So for testing some of this stuff on
the engine store. One thing we're going to need is a Phillips screwdriver that allow
us to get into the door and actually access what's going on
inside there and we might also require something to test
for power. In this case. We can use something like a test light. This is
a 12 volt test light can actually use a 9 volt battery or we
could use a voltmeter as well.
Okay, right here is where we have the contact points for the keyless entry.
These are the contact points that are controlling the
keyless entry lock. So this is where the power is going to be coming from. These contact
points will be touching these posts right here when the
door is closed. So these are the points right here where we want to test to
see if they actually have power or not whenever you hit the keyless entry
lock.
As soon as you hit the locker unlock it'll get a pulse from this
and it'll actually contact here on the door. You see there's
two posts on the door here as well. That sends the power up to the
actuator inside the door. So every time you hit the the lock
and unlock for the chassis, you'll get power here. So in
order to test for the power there you're gonna need either the voltmeter or
the test light.
So we can show you real quick what will happen. We'll put the cable terminal
on one side here and one on there.
and then when we hit the locker unlock
you'll see there's a bit of a pulse. So you've added for only
lasts for about a second and the polarity will reverse depending on which way
if you're hitting Locker Unlocked, so it'll the polarity
will reverse so you won't have constant power there
as you can see the test light it doesn't light up at all right now, but it'll
only light up whenever the button is pressed for locking it.
or
Unlocking if you want to check for power using a volt
meter that can be done as well. So we're gonna take the voltmeter we're gonna
change the voltmeter over to DC volts.
So we'll change it over to DC volts
as well. Again take the the two test
leads.
And we'll put them onto the onto these pads. We'll
hit the lock and unlock.
And you'll see there's just a quick flash of voltage there and it'll
go back to zero again. And again that voltage will be reverse
polarity. If you're going the opposite direction to lock
versus unlock. So what you can find here as well as if these
terminals are at all corroded or dirty, if you
give them a good cleaning you can use either some Scotch bite or something like that
or some light sandpaper will actually work well to just clean
these terminals off a little bit and then a light coating of some sort of a lubricant
just to prevent corrosion that usually helps to make sure
there's a good clean contact to the posts. If you do have power
here and you feel that there's a
good contact being made here what we can do then is test further inside
the door to see if we have power inside there. So another way we can
check to see if we have good contact is we'll close the door
just far enough that we can actually still see the deadbolt, but now the
contact should be touching down below. So now if we lock and
unlock the door
You should see the deadbolt move right now.
If it still doesn't move when the door is closed this far then we
may want to take a look inside the door and see what's going on there. So the wires
from the from the door here, they're gonna be running from the posts. They're
gonna be running up into the door and to an actuator behind this cover plate.
So in order to access that a couple screws to remove
here and just loosen off these screws to allow this plate to
come out.
So we'll just loosen off these screws first using a Phillips screwdriver.
And then we'll get in here and we'll remove these two screws.
Once those screws are out and these are loose you should be able to slide this
completely out. And this is where you can see the wires that are coming from
down below there in behind here is the actuator that
actually controls the the deadbol coming
in and out. But what we'll do here is we'll make sure that these wires
actually have power as well.
And you will notice that the color may not matter that's depending
on if how it's hooked up from Factory. So just
pay attention to the color right now. You can see this one is actually hooked up
green to blue and and blue to green over here as well. So it just
pay attention to that and you may need to change just depending on
if it's Locker unlock on what direction the deadbolt is actually moving. Okay.
So what we're going to do is we're just gonna unhook these wires. They're
just push connector. So we're just gonna pull them apart.
without wrecking them
Once you have disconnected, you have the two terminals going to this actuator.
And two terminals that are coming down from the bottom of
the door.
So if we want to test this for power you can test it for power right
now, but because we have the door open the contacts
are not touching down below. So we'll actually have to have the door closed
in order to have those contacts touching as well. So here again, we can
see the wires. These are the ones coming from the bottom of the door. These are the
ones going to the actuator up here. We don't need to test these because these are obviously
not hooked up to anything, but we'll take these wires here.
And again polarity doesn't really matter with this. We're just
checking to see if it has any power at all.
So we'll put our terminals into there to make sure that we're testing it.
Once we have it on we'll hit the lock and unlock.
And you can see that we do have power there. We'll check it on the
unlock as well.
And yes, we do have power. So the wires should