So Ryan, can we talk a little bit about
the settings screen now?
Sure. So to get to the settings, you go
to this little gear icon here. So you
head into there. So there's a number of
different settings here. So the first
button we'll talk about is cleaning
mode. So, say you get a lot of finger
fingerprints on your screen, you press
this cleaning mode button and it will
disable the screen for 15 seconds. So,
as you can see, I can just kind of touch
it for a while and nothing will happen
until 15 seconds elapses and then it
will revert back to where it was before.
So, the second button here is switch
panel info. So, the switch panels are
the other wireless switches that are
located throughout the coach that
control your other lights and water pump
for the areas that they're in. So here
it will show that there is an entry
switch, a galley switch, a washroom
switch, and a bedroom switch. So if one
of your switches isn't functioning
correctly, you would go to this screen
and see if it is showing a green or red
icon here for this little wireless
symbol.
Why would it turn red?
So it will turn red if the battery dies
in the switch or or just for some other
reason that the switch becomes
disconnected.
How do you uh reconnect the switch or
how do you pair it again? Say this
becomes red. What you do is press and
hold on the switch that you would like
to pair for 5 seconds
and it'll come up. It'll say wireless
switch panel pairing procedure. So it'll
all explain it here, but all you have to
do is click start pairing and then you
just go to the switch panel in question.
So here I selected the galley. You would
press any two buttons for 5 seconds
and it'll show that the switch has
paired successfully.
Okay. So, Ryan, network diagnostics. How
is that going to help us? What does that
show?
So, the network diagnostics, if you're
having problems, you can head into here.
And so, it shows the status of each of
the modules that are connected. So, here
is your 7-in color LCD. That's this
display here. The G9 is the actual
brains of the system, and that location
will vary depending on your coach. And
your aircon, that's what's controlling
your air conditioner,
as well as the outputs from the air con.
So, heat pump, compressor, fan high, fan
low, and your freeze sensor. So, here
it'll show a little green dot indicating
that they're working correctly. And so,
here, if you click on this G9 button,
here's all your G9 outputs and inputs.
Again, if the light is green, it's
working correctly and on. If the light
is off, then it's just off. And if it's
red, then there's an error present. And
often just turning off and on the output
will reset the error. If the error
persists, then you'll need to call
service. So, after network diagnostics,
here again, we have our degrees Celsius
and degrees Fahrenheit. You can choose
whichever one you want. Whichever one's
blue is the one that's active. Down
here, it'll show your floor plan. So,
right now, we're filming this in a 24
MB. Up here is your screen brightness.
So, this can change the brightness of
the screen on here. You can also press
this auto dimming button. And so then
your screen will automatically dim based
on the brightness of the area. So that
when you're sleeping, it will actually
be fully dimmed and asleep.
And as well here you can set your time.
So you just go up with hours or minutes.
And you can change between a 24-hour
clock or a 12-h hour clock. And right
here at the bottom, you'll see something
that says GUI version and logic
controller version. So, if you do have
to call into service either Firefly or E
RV or Leisure Travel Vans, we might ask
you for these numbers and this is where
you would find them.
So, Ryan, let's suppose I just installed
an aftermarket satellite dish on the
roof. How could I turn the power on for
that?
So, if you install a satellite dish, you
go into your settings here. So, where it
shows floor plan, you press and hold on
that floor plan for about 10 seconds.
And then there will be a warning here.
And so here you could change the floor
plan layout, which you won't want to do
cuz you're not actually changing your
floor plan. But here there's an out
option here for your satellite power.
You just press that and the little green
light comes on. You hit confirm. And now
if you go back to your homepage, you'll
see that there's a satellite power
button. So you just push that button and
it comes on. That means your satellite
has power.
Yeah.
Heat.